《理工科本科生毕业论文（设计）格式模板》（学生用）

附件六

Abstract

□□空一行 Times New Roman 三号加粗居中 □□正文Times New Roman 四号。英文内容摘要300个词左右。 □□空一行 Key words：□×××××××××□□×××××××××□□×××××××××□□××××××××××□×××××××××

Times New Roman 四号，与中文关键词相对应 Times New Roman 四号加粗左对齐

5

以上内容均在一页，不标页码

附件七：

目 录(宋体三号加粗) （空一行） 1 (黑体 4号 加粗) ··································································· 1 1．1(宋体4号) ··········································································· 1 1．1．1(宋体4号) ······································································· 1 1．1．2.(宋体4号) ······································································· 4 1．2(宋体4号) ··········································································· 7 1．3(宋体4号) ········································································· 12 2 (黑体 4号 加粗) ···································································· 16 2．1(宋体4号) ·········································································· 16 2．2(宋体4号) ········································································· 24 2．2．1(宋体4号) ······································································ 24 2．2．2(宋体4号) ······································································· 30 2．2．3(宋体4号) ······································································· 31 2．3(宋体4号) ········································································· 33 3 (黑体 4号 加粗) ···································································· 36 3．1(宋体4号) ········································································· 38 3．2(宋体4号) ········································································· 43 4 (黑体 4号 加粗) ···································································· 45 参考文献(黑体 4号 加粗) ························································ 48 附录 (黑体 4号 加粗) ···························································· 50 致谢

6

（注：目录行间距为25磅） 论文正文的排版： 1.换章必须换页，没按章节安排结构的无须换页（本专业不换页） 2. 第一级标题用三号粗黑体，左顶格上下空一行 3. 第二级标题用小三黑体，左顶格前后空半行 4 第三级标题用四号黑体，左顶格不空行 5. 正文小四号字宋体，行距为固定值20磅

6. 图（表）名必须有中英文，5号黑体，图中文字用5号宋体

7. 参考文献另起一页，参考文献标题用三号粗黑体，居中上下空一行，参考文献正文为五号宋体

8. 附录标题用三号粗黑体 ，居中上下空一行，附录正文为小四号宋体 9．致谢标题用三号粗黑体 ，居中上下空一行，致谢正文为小四号宋体 有关论文排版的其它说明：

1．纸张大小及版心：统一用A4纸（210mm×297mm）打印，边距设为： 上 2.54cm，下 2.54cm，左 3cm，右 2.2cm。行距为固定值20磅。

2．注意文中代表变量的英文字母必须用斜体，其它用正体。微分号d、圆周率π、自然底数e、矩阵转置T均应为正体。 3．文章中的英文均用Times New Roman 字体。 4．毕业论文格式的电子版为Word文件。

5．所有度量单位用英文单位，如kg、Km、hm2等。

6．正文内容部分均设页眉，左为“广东商学院×××××学院”，右为论文题目，小5黑体。页脚为页码，5号黑体，居中。 7．正文首页不再写论文题目。

附件七：

7

参□考□文□献

□□空一行

黑体三号居中

文后各类参考文献表编排规范格式要求参见“附件一”相关内容。 字体要求；中文参考文献 宋体五号。英文参考文献 Times New Roman五号

此部分接着论文正文部分编排页码，页码位置与论文正文相同 8