巴可DP2K系列故障代码

76.Code 5451: “heat exchanger fan - voltage high” (Warning) “换热器风扇 - 电压高”

77.Code 5452: “heat exchanger fan - voltage too low” (Error) “换热器风扇 - 电压过低”

78.Code 5453: “heat exchanger fan - voltage low” (Warning) “换热器风扇 - 电压低”

79.Code 5461: “lamp anode fan - voltage high” (Warning) “灯阳极风扇 - 电压高”

80.Code 5462: “lamp anode fan - voltage too low” (Error) “灯阳极风扇 - 电压过低”

81.Code 5463: “lamp anode fan - voltage low” (Warning) “灯阳极风扇 - 电压低”

82.Code 5471: “lamp cathode fan - voltage high” (Warning) “灯阴极风扇 - 电压高”

83.Code 5472: “lamp cathode fan - voltage too low” (Error) “灯阴极风扇 - 电压过低”

84.Code 5473: “lamp cathode fan - voltage low” (Warning) “灯阴极风扇 - 电压低”

85.Code 5492: “smps fan - voltage too low” (Error) “风扇控制板风扇 - 电压过低”

86.Code 5493: “smps fan - voltage low” (Warning) “风扇控制板风扇 - 电压低”

87.Code 5501: “fib +12v - voltage high” (Warning) “解码板 +12v - 电压过高”

88.Code 5503: “fib +12v - voltage low” (Warning) “解码板 + 12v - 电压低”

9

89.Code 5521: “motor (lens, dowser) - voltage high” (Warning) “马达（镜头、光闸） - 电压高”

90.Code 5523: “motor (lens, dowser) - voltage low” (Warning) “马达（镜头、光闸） - 电压低”

91.Code 5531: “pump - voltage high” (Warning) “冷却泵 - 电压高”

92.Code 5532: “pump - voltage too low” (Error) “冷却泵 - 电压过低”

93.Code 5533: “pump - voltage low” (Warning) “冷却泵 - 电压低”

94.Code 5551: “tec - voltage high” (Warning) “珀耳贴致冷器 - 电压高”

95.Code 5553: “tec - voltage low” (Warning) “珀耳贴致冷器 - 电压低”

96.Code 5561: “elcabox fan - voltage high” (Warning) “电控盒风扇 - 电压高”

97.Code 5562: “elcabox fan - voltage too low” (Error) “电控盒风扇 - 电压过低”

98.Code 5563: “elcabox fan - voltage low” (Warning) “电控盒风扇 - 电压低”

99.Code 5571: “lamp rear fan - voltage high” (Warning) “灯后部风扇 - 电压高”

100.Code 5572: “lamp rear fan - voltage too low” (Error) “灯后部风扇 - 电压过低”

101.Code 5581: “+12v - voltage high” (Warning) “+12v - 电压高”

10

102.Code 5583: “+12v - voltage low” (Warning) “+12v - 电压低”

103.Code 5640: “lamp power supplies - zero lamp power supplies detected” (Error)

“灯电源 - 没有探测到灯电源” 状态 两电源模块其中之一主供电电缆断开 解决方法 检查电源模块上MAINS INPUT插槽及插线 电源模块中“CTRL IN”与“CTRL OUT”检查电源模块中“CTRL IN”与“CTRL 插线断开 OUT”插槽及插线 电源模块未安装到位 灯电源控制板失灵 灯电源模块闪红灯 重新安装 更换 更换电源模块 104.Code 5641: “lamp power supplies - lamp is on, but smps is off” (Error) 状态 开关电源板失灵 灯电源模块失灵 电源背板失灵 更换 更换 更换 解决方法 105.Code 5642: “lamp power supplies - at least one lamp power supply could not be detected” (Error) 参见5640

106.Code 5643: “lamp power supplies - communication failed with at least one lamp power supply”(Error) 参见5640

107.Code 5644: “lamp power supplies - lamp is on, but at least one lamp power supply is off” (Error) 参见5640

11

108.Code 5646: “lamp - set lamp on failed” (Error) “灯 - 点灯失败” 状态 氙灯有触发，无法持续点燃 解决方法 1，氙灯寿命将尽，更换新灯 2，触发器损坏 109.Code 5647: “lamp - lamp is off due to an error” (Error) “灯 - 由于一个错误氙灯已熄灭” 状态 解决方法 由于某些错误，灯电源被指令熄灭氙灯 查看放映机日志寻找其他错误信息，首先解决此类错误问题 灯电源故障 查看灯电源指示灯，若红灯闪烁则更需换灯电源 更换新灯 氙灯缺陷 110.Code 5654: “lamp run time - read failed” (Error) “灯运行时间 - 读取失败”

111.Code 5657: “lamp run time - exceeds maximum” (Error) “灯运行时间 - 已到最大寿命” 状态 灯箱内氙灯已达到最大使用寿命 解决方法 更换新灯，或重置灯信息 112.Code 5658: “lamp run time - read limits failed” (Error) “灯运行时间 - 限制读取失败”

113.Code 5659: “lamp run time - warning” (Warning) 状态 灯箱内氙灯接近到最大使用寿命 解决方法 尽快更换新灯，或重置灯信息 114.Code 5800: “ti-boards - system status = fail” (Error) “TI板 - 系统状态=失败”

这是一个通用TI错误代码，需要进入触摸屏的“诊断-测试-自检”中勾选所

12