局域网技术与组网工程课程设计

RouterA(config-subif)#encap dot1q 90

RouterA(config-subif)#ip add 172.18.9.1 255.255.255.0 RouterA(config-subif)#no shutdown RouterA(config-subif)#exit RouterA(config)# （10）、给vlan100配置 RouterA(config)#int fa0/0.10

%LINK-5-CHANGED: Interface FastEthernet0/0.10, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.10, changed state to up RouterA(config-subif)#encap dot1q 100

RouterA(config-subif)#ip add 172.18.10.1 255.255.255.0 RouterA(config-subif)#no shutdown RouterA(config-subif)#exit RouterA(config)# （11）、给vlan110配置 RouterA(config)#int fa0/0.11

%LINK-5-CHANGED: Interface FastEthernet0/0.11, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.11, changed state to up RouterA(config-subif)#encap dot1q 110

RouterA(config-subif)#ip add 172.18.11.1 255.255.255.0 RouterA(config-subif)#no shutdown RouterA(config-subif)#exit RouterA(config)# （12）、给vlan120配置 RouterA(config)#int fa0/0.12

%LINK-5-CHANGED: Interface FastEthernet0/0.12, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.12, changed state to up RouterA(config-subif)#encap dot1q 120

RouterA(config-subif)#ip add 172.18.12.1 255.255.255.0 RouterA(config-subif)#no shutdown RouterA(config-subif)#exit RouterA(config)# （13）、给vlan130配置 RouterA(config)#int fa0/0.13

%LINK-5-CHANGED: Interface FastEthernet0/0.13, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.13, changed state to up RouterA(config-subif)#encap dot1q 130

RouterA(config-subif)#ip add 172.18.13.1 255.255.255.0 RouterA(config-subif)#no shutdown RouterA(config-subif)#exit RouterA(config)# （14）、给vlan140配置 RouterA(config)#int fa0/0.14

%LINK-5-CHANGED: Interface FastEthernet0/0.14, changed state to up

16

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0.14, changed state to up RouterA(config-subif)#encap dot1q 140

RouterA(config-subif)#ip add 172.18.14.1 255.255.255.0 RouterA(config-subif)#no shutdown RouterA(config-subif)#exit RouterA(config)#

7.2、交换机的配置

在交换机上划分vlan

Switch>en Switch#conf t

Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#vlan 1

Switch(config-vlan)#name fuwuqi1

Default VLAN 1 may not have its name changed. Switch(config-vlan)#exit Switch(config)#vlan 2

Switch(config-vlan)#name fuwuqi2 Switch(config-vlan)#exit Switch(config)#vlan 3

Switch(config-vlan)#name fuwuqi3 Switch(config-vlan)#exit Switch(config)#vlan 4

Switch(config-vlan)#name fuwuqi4 Switch(config-vlan)#exit Switch(config)#vlan 10

Switch(config-vlan)#name jiaoxue1 Switch(config-vlan)#exit Switch(config)#vlan 20

Switch(config-vlan)#name jiaoxue2 Switch(config-vlan)#exit Switch(config)#vlan 30

Switch(config-vlan)#name xueshengxushe1 Switch(config-vlan)#exit Switch(config)#vlan 40

Switch(config-vlan)#name xueshengsushe2 Switch(config-vlan)#exit Switch(config)#vlan 50

Switch(config-vlan)#name jiaoshisushe1 Switch(config-vlan)#exit Switch(config)#vlan 60

Switch(config-vlan)#name xiaojing

17

Switch(config-vlan)#exit Switch(config)#vlan 70

Switch(config-vlan)#name zonghe Switch(config-vlan)#exit Switch(config)#vlan 80

Switch(config-vlan)#name jiaoshisushe2 Switch(config-vlan)#exit Switch(config)#vlan 90

Switch(config-vlan)#name jiaoxue Switch(config-vlan)#exit

将端口划分到相应的vlan中

Switch(config)#int range fa 0/1-35

Switch(config-if-range)#switchport mode access Switch(config-if-range)#switchport access vlan 10 Switch(config-if-range)#no shut Switch(config-if-range)#exit

Switch(config)#int range fa 0/1-35

Switch(config-if-range)#switchport mode access Switch(config-if-range)#switchport access vlan 20 Switch(config-if-range)#no shut Switch(config-if-range)#exit

Switch(config)#int range fa 0/1-28

Switch(config-if-range)#switchport mode access Switch(config-if-range)#switchport access vlan 30 Switch(config-if-range)#no shut Switch(config-if-range)#exit

Switch(config)#int range fa 0/1-28

Switch(config-if-range)#switchport mode access Switch(config-if-range)#switchport access vlan 40 Switch(config-if-range)#no shut Switch(config-if-range)#exit

Switch(config)#int range fa 0/1-16

Switch(config-if-range)#switchport mode access Switch(config-if-range)#switchport access vlan 50 Switch(config-if-range)#no shut Switch(config-if-range)#exit Switch(config)#int range fa 0/1-3

Switch(config-if-range)#switchport mode access Switch(config-if-range)#switchport access vlan 60 Switch(config-if-range)#no shut Switch(config-if-range)#exit

18

Switch(config)#int range fa 0/1-27

Switch(config-if-range)#switchport mode access Switch(config-if-range)#switchport access vlan 70 Switch(config-if-range)#no shut Switch(config-if-range)#exit

Switch(config)#int range fa 0/1-16

Switch(config-if-range)#switchport mode access Switch(config-if-range)#switchport access vlan 80 Switch(config-if-range)#no shut Switch(config-if-range)#exit

Switch(config)#int range fa 0/1-35

Switch(config-if-range)#switchport mode access Switch(config-if-range)#switchport access vlan 90 Switch(config-if-range)#no shut Switch(config-if-range)#exit

设置端口模式

Switch>en Switch#conf t

Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#inter f0/2

Switch(config-if)#switchport mode trunk

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2, changed state to up Switch(config-if)#exit Switch(config)#inter f0/4

Switch(config-if)#switchport mode trunk

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to down %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/4, changed state to up Switch(config-if)#exit

在交换机SWITCH2上划分vlan

Switch(config)#vlan 10

Switch(config-vlan)#name jiaoxue1 Switch(config-vlan)#exit Switch(config)#vlan 20

Switch(config-vlan)#name jiaoxue2 Switch(config-vlan)#exit Switch(config)#vlan 30

Switch(config-vlan)#name xueshengxushe1 Switch(config-vlan)#exit

19