鍖婚櫌璁惧�囩�＄悊绯荤粺_璐哄窞甯備汉姘戝尰闄㈣�惧�囩�戜俊鎭�鍖栫�＄�?- 鐧惧害鏂囧簱

医院设备管理系统_贺州市人民医院设备科信息化管理

step shape, control of step size, set aside a decoration project, to run up and down the stairs the same fa?ade stepping angle. 4.4 reverse triangular plate is in the Middle bench, reinforcement time side boards. Reverse triangular plates consist of a number of triangular pieces of wood nailed to the wood, and two triangular wood blocks high and wide of the right angle equal to step on a side, timber section for 50mmx100mm and third corner Board with bench support cross-ridged fixed between the side plates. 4.4 (1) expansion joints template support set: first support good expansion joints side of wall template (wall sides are for multilayer Board), stay its concrete pouring Hou, will its template demolition, again support another side wall template, but this wall by expansion joints side with 200 thick high-density squeeze plastic poly benzene Board for template, another side for multilayer Board, expansion joints North-South State surface the with 200x200 thick multilayer Board box for across die, to control expansion joints of upper and lower vertical degrees. 4.4 (2) treatment of construction joints: this construction is not the principle of construction joints, such as construction joints, subject to the following requirements: construction joint in beam and plate with steel mesh or wood-mode blocked. Attention to the retention of construction joints must be perpendicular to the axis of the beam and plate, shall remain oblique Cha. Before the next concrete pouring, construction joints of concrete should be cutting hair, and loose stones should be left floating pulp, water and moist. 5

construction considerations 5.1 template installation, upper and lower column formwork system should be installed on the same vertical line. 5.2 templates on each floor after installation, should release agent brush template. 5.3 for the joints is greater than 2mm, paste the crack tape. 5.4 no hard hit when stripping pry, to prevent damage to the template and the pouring of concrete. 6 quality standard for reached concrete of standard, we according to concrete structure engineering construction quality acceptance standard (GB50204-2002) developed has internal control standard, as Xia by shows: concrete quality internal control standard project allows deviation national standards internal control standard axis location 5 3 end of die Shang surface elevation ? 5 ? 3 adjacent two Board surface level poor 2 2 surface flat degrees 5 3 pre buried plate center line location 3 3 pre buried tube, and reserved hole center line location 3 3 pre buried bolt center line location 2 2 Exposed length +10,0 +10,0 reserved hole center line position 10 10 section size +10,0 +10,0 reinforcing the centerline location 5 5 exposed length +10,0 +10,0 die frame support must have sufficient strength, rigidity and stability, supporting parts must have sufficient support area. Template size is accurate, seam marks neat and orderly. Structures of yin and Yang founder straight, joint width shall not exceed

医院设备管理系统_贺州市人民医院设备科信息化管理

贺州市人民医院自1926年2月创办以来，已经走过近90年的岁月长河。现全院占地36110.85平方，固定资产总值5亿多元，拥有贺州市设施最先进的现代化住院大楼，是全市规模最大的一家综合性医院。

在医院设备方面，数量庞大，品种繁多，拥有1.5T核磁共振、六十四排CT、双光子直线加速器、大C臂、双台DR、原装进口美国贝克曼生化免疫流水线、高等级B超、高压氧舱、体外循环机、CRRT(血液净化)、骨密度仪、乳腺X光机等先进的诊疗抢救设备。

随着医院的快速发展，医疗服务事业迅速扩大，越来越多的先进设备被引进，对于后勤设备科的管理要求也相应越来越高。

但由于设备科在医院长期处于比较忽视的状态，大量设备的引入使管理出现了更多的问题:

1、台账混乱不清，设备科无法全面并快速掌握全院的物资账目，甚至分布在哪些科室也都只是知道个大概。

2、设备的运行状态需要到临床查看才知道，加重人工工作量。 3、每到提交报表的时候都需要加班来统计对比，耗时耗力。

4、一年一次的盘点很费时费力，加上本身账目有问题，导致很多时候进行盘点也是应and tamping, clear template prior to placing the debris, and water wet template; control since the height of the concrete shall not exceed 1.5M; dense wall bushing with the same level of fine aggregate concrete for pouring concrete pouring, pouring top layered slopes and

adjacent two layers of pouring interval must not exceed 1h. Strengthen the maintenance of waterproofing concrete, the baseboard after the concrete has been poured, immediately cover it with plastic sheeting and strengthening conservation. Strengthen the construction quality control of construction joints, horizontal construction joints for Foundation slab, set plate sealing strip, the construction of water stop steel concrete compacting. In front of the poured concrete walls, the joint surfaces for cutting hair, remove floating particles, and rinse to keep moist. VI reinforcement Engineering (a) steel raw material requirements of the engineering design of main structure of steel primary steel and grade of steel. Steel comes into play, should be accompanied by the manufacturer's quality certificate, and Visual inspection by the engineering technology, materials, personnel, including specifications, diameter tolerance, have no cracks, pores, surface corrosion. In all of steel quality certificate complete Shi, by test room by batch sampling do retest, each bulk is unlikely to Yu 60t, each acceptance batch in the take sample a group, including 2 root pull, and 2 root bent try pieces, 5 root size, and weight try pieces, try pieces from any three root (or two disc) steel in the interception, each root steel Shang cutstep shape, control of step size, set aside a decoration project, to run up and down the stairs the same fa?ade stepping angle. 4.4 reverse triangular plate is in the Middle bench, reinforcement time side boards. Reverse triangular plates consist of a number of triangular pieces of wood nailed to the wood, and two triangular wood blocks high and wide of the