网络项目工程综合实训报告

.

[RT1]interface Serial 0/1/1

[RT1-Serial0/1/1]description link-to-S0/1/0 [RT1]interface Serial 0/1/2

[RT1-Serial0/1/2]description link-to-S0/1/3 [RT1]interface Mp-group 0

[RT1-Mp-group0]ip address 192.168.0.9 30 [RT1-Mp-group0]int s0/1/1

[RT1-Serial0/1/1]ppp mp Mp-group 0 [RT1-Serial0/1/1]

Tc 22 17:49:29:587 2015 RT1 IFNET/3/LINK_UPDOWN: Serial0/1/1 link status is DOWN.

Tc 22 17:49:29:587 2015 RT1 IFNET/5/LINEPROTO_UPDOWN: Line protocol on the interface Serial0/1/1 is DOWN.

Tc 22 17:49:29:587 2015 RT1 IFNET/3/LINK_UPDOWN: Serial0/1/1 link status is UP.

Tc 22 17:49:29:618 2015 RT1 IFNET/5/LINEPROTO_UPDOWN: Line protocol on the interface Serial0/1/1 is UP.

[RT1-Serial0/1/1]int s0/1/2 [RT1-Serial0/1/2]ppp mp Mp-group 0 [RT1-Serial0/1/2]

Tc 22 17:51:01:300 2015 RT1 IFNET/3/LINK_UPDOWN: Serial0/1/2 link status is DOWN.

Tc 22 17:51:01:300 2015 RT1 IFNET/5/LINEPROTO_UPDOWN: Line protocol on the interface Serial0/1/2 is DOWN.

Tc 22 17:51:01:300 2015 RT1 IFNET/3/LINK_UPDOWN: Serial0/1/2 link status is UP.

Tc 22 17:51:01:316 2015 RT1 IFNET/5/LINEPROTO_UPDOWN: Line protocol on the interface Serial0/1/2 is UP.

第2步：配置SZ

..

.

[RT2]interface Serial 0/1/1

[RT2-Serial0/1/1]description link-to-s0/1/0 [RT2-Serial0/1/1]ip address 192.168.0.6 30 [RT2-Serial0/1/1]

Tc 22 17:53:04:477 2015 RT2 IFNET/5/PROTOCOL_UPDOWN: Protocol PPP IPCP on the interface Serial0/1/1 is UP.

第3步：配置SH

[RT3]interface Serial 0/1/3

[RT3-Serial0/1/3]description link-to-s0/1/2 [RT3-Serial0/1/3]int s0/1/0

[RT3-Serial0/1/0]description link-to-s0/1/1 [RT3-Serial0/1/0]quit [RT3]interface Mp-group 0

[RT3-Mp-group0]ip address 192.168.0.10 30 [RT3-Mp-group0]int [RT3-Mp-group0]int s0/1/3

[RT3-Serial0/1/3]ppp mp Mp-group 0 [RT3-Serial0/1/3]

Tc 22 17:56:03:607 2015 RT3 IFNET/3/LINK_UPDOWN: Serial0/1/3 link status is DOWN.

Tc 22 17:56:03:607 2015 RT3 IFNET/5/LINEPROTO_UPDOWN: Line protocol on the interface Serial0/1/3 is DOWN.

Tc 22 17:56:03:732 2015 RT3 IFNET/3/LINK_UPDOWN: Serial0/1/3 link status is UP.

Tc 22 17:56:03:748 2015 RT3 IFNET/5/LINEPROTO_UPDOWN: Line protocol on the interface Serial0/1/3 is UP.

Tc 22 17:56:03:748 2015 RT3 IFNET/3/LINK_UPDOWN: Mp-group0 link status is UP.

Tc 22 17:56:03:748 2015 RT3 IFNET/5/LINEPROTO_UPDOWN: Line

..

.

protocol on the interface Mp-group0 is UP.

Tc 22 17:56:03:748 2015 RT3 IFNET/5/PROTOCOL_UPDOWN: Protocol PPP IPCP on the interface Mp-group0 is UP.

[RT3-Serial0/1/3]int s0/1/0 [RT3-Serial0/1/0]ppp mp Mp-group 0 [RT3-Serial0/1/0]

Tc 22 17:56:24:356 2015 RT3 IFNET/3/LINK_UPDOWN: Serial0/1/0 link status is DOWN.

Tc 22 17:56:24:356 2015 RT3 IFNET/5/LINEPROTO_UPDOWN: Line protocol on the interface Serial0/1/0 is DOWN.

Tc 22 17:56:24:356 2015 RT3 IFNET/3/LINK_UPDOWN: Serial0/1/0 link status is UP.

Tc 22 17:56:24:371 2015 RT3 IFNET/5/LINEPROTO_UPDOWN: Line protocol on the interface Serial0/1/0 is UP.

4.3路由部署 （描述相关设备及每个设备详细配置）

考虑到该公司未来的发展战略规划，在部署路由时，全网采用动态的OSPF协议，并规划每个办事处为一个Area，这样如果以后网络规模扩大，也不需要对整个网络重新规划，而只需增加Area即可。为了方便对各个办事处访问外网的控制，规划这个网络的公司出口设在总部，由总部统一出口访问外网，在总部与外网之间使用默认路由。

第1步：SW1交换机路由配置

手工指定 router id,为 VLAN 1 的接口地址 [SW1]router id 192.168.0.25 [SW1]ospf

[SW1-ospf-1]area 1

在区域里发布网段,后面跟的是反掩码,但有些地址我们很难口算出它的反掩码,CMW提供了这样一个特性,可以将掩码自动转化为反掩码,为此我们演示一下,发布网段时使用掩码,并验证是否能自动转换。

[SW1-ospf-1-area-0.0.0.1]net 192.168.1.0 255.255.255.0

..

.

验证是否能自动将掩码转换成反掩码 [SW1-ospf-1-area-0.0.0.1]dis this #

area 0.0.0.1

network 192.168.1.0 0.0.0.255 # return

#发布同 RT1路由器互连接口地址

[SW1-ospf-1-area-0.0.0.1]net 192.168.0.1 0.0.0.3 #发布交换机管理 VLAN 地址网段

[SW1-ospf-1-area-0.0.0.1]net 192.168.0.24 0.0.0.7 第2步：RT1路由器路由配置 创建并进入 loopback 0 接口 [RT1]int loop 0

为 loopback 0 接口配置 IP 地址,注意掩码为 32 位 [RT1-LoopBack0]ip add 192.168.0.17 32 手工指定 router id

[RT1]router id 192.168.0.17 [RT1]ospf

创建并进入 area 1 [RT1-ospf-1]area 1

发布同 BJ-S5626C-0 的互连网段

[RT1-ospf-1-area-0.0.0.1]net 192.168.0.0 0.0.0.3 为了便于管理,发布 loopback 接口地址,作为网管地址. [RT1-ospf-1-area-0.0.0.1]net 192.168.0.17 0.0.0.0 创建并进入 area 0 [RT1-ospf-1]area 0

#发布同 RT2 及RT3 的互连网段

[RT1-ospf-1-area-0.0.0.0]net 192.168.0.4 0.0.0.3

..