LTE杂散及部分接收项测试 - 图文

Table 6.6.3.3.4.1-2: Test Configuration Table (network signalled value \

Initial Conditions Test Environment (as specified in TS 36.508 [7] subclause 4.1) Test Frequencies (as specified in TS36.508 [7] subclause 4.3.1) Test Channel Bandwidths (as specified in TS 36.508 [7] subclause 4.3.1) Test Parameters for Channel Bandwidths Test Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 10MHz 10MHz 10MHz 10MHz 10MHz 10MHz 10MHz 10MHz 10MHz 10MHz 10MHz 10MHz 10MHz 10MHz 10MHz 10MHz N/A for Additional Spurious Emissions testing. QPSK QPSK QPSK QPSK QPSK 16QAM QPSK QPSK 16QAM QPSK 16QAM QPSK QPSK QPSK QPSK 16QAM 1 8 6 20 12 36 (Note 1) 16 12 16 30 30 (Note 1) 6 2 50 12 50 (Note 1) Note 1: Applies only for UE-Categories 2-5 43 48 0 0 0 19 19 19 19 19 0 0 13 13 13 13 Ch BW Downlink Configuration Mod’n RB allocation Mod’n Uplink Configuration RB allocation RB_start NC Mid range 10MHz Table 6.6.3.3.4.1-3: Test Configuration Table (network signalled value “NS_08”)

Initial Conditions Test Environment as specified in TS 36.508[7] subclause 4.1 Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 Test Channel Bandwidths as specified in TS 36.508 [7] subclause 4.3.1 Test Parameters for Channel Bandwidths Ch BW 5MHz 5MHz 5MHz 10MHz 10MHz 10MHz 10MHz 10MHz 10MHz 10MHz 15MHz 15MHz 15MHz 15MHz 15MHz 15MHz 15MHz Downlink Configuration Mod’n RB allocation FDD testing TDD QPSK QPSK QPSK QPSK QPSK QPSK QPSK QPSK QPSK 16QAM QPSK QPSK QPSK QPSK QPSK QPSK 16QAM Uplink Configuration Mod’n RB allocation FDD 1 8 25 1 12 27 36 40 50 50 (Note 3) 1 16 27 36 40 75 75 (Note 3) Note 1: The 1 RB allocation shall be tested at both RB #0 and RB #max. Note 2: The starting resource block of partial RB allocation shall be RB#0 and RB# (max + 1 - RB allocation) of the channel bandwidth Note 3: Applies only for UE-Categories 2-5 TDD N/A 5MHz, 10MHz, 15MHz High range Normal N/A for Additional Spurious Emissions

Table 6.6.3.3.4.1-4: Test Configuration Table (network signalled value “NS_09\

Initial Conditions Test Environment as specified in TS 36.508[7] subclause 4.1 Test Frequencies as specified in TS36.508 [7] subclause 4.3.1 Test Channel Bandwidths as specified in TS 36.508 [7] subclause 4.3.1 Test Parameters for Channel Bandwidths Ch BW 5MHz 5MHz 5MHz 10MHz 10MHz 10MHz 10MHz 10MHz 15MHz 15MHz 15MHz 15MHz 15MHz 15MHz Downlink Configuration Mod’n RB allocation FDD testing TDD QPSK QPSK QPSK QPSK QPSK QPSK QPSK 16QAM QPSK QPSK QPSK QPSK QPSK 16QAM Uplink Configuration Mod’n RB allocation FDD 1 8 25 1 12 40 50 50 (Note 3) 1 16 40 54 75 75 (Note 3) Note 1: The 1 RB allocation shall be tested at both RB #0 and RB #max. Note 2: The starting resource block of partial RB allocation shall be RB#0 and RB# (max + 1 - RB allocation) of the channel bandwidth Note 3: Applies only for UE-Categories 2-5 TDD N/A 5MHz, 10MHz, 15MHz High range Normal N/A for Additional Spurious Emissions 从以上几个表中的要求可以看出，在NS_05；NS_07；NS_08；NS_09这几项时，分别对应于BAND1;BAND13;BAND19;BAND21。所以我们在测试额外杂散时也要注意在不同的NS值下只测试以上相对应的BAND即可。

4. 协议要求

Table 6.6.3.3.5.1-1: Additional requirements (PHS) test requirements（NS-05） Frequency band (MHz) 5 MHz 1884.5 ??f ?1919.6 1884.5 ??f ?1915.7 *2*1Channel bandwidth / Spectrum emission limit (dBm) 10 MHz -41 -41 15 MHz -41 -41 20 MHz -41 -41 Measurement bandwidth -41 -41 300 KHz 300 KHz NOTE 1: Applicable when the lower edge of the assigned E-UTRA UL channel bandwidth frequency is larger than or equal to the upper edge of PHS band (1919.6 MHz) + 4 MHz + the Channel BW assigned, where Channel BW is as defined in sub-clause 5.4.2. Operations below this point are for further study. NOTE 2: Applicable when the lower edge of the assigned E-UTRA UL channel bandwidth frequency is larger than or equal to the upper edge of PHS band (1915.7 MHz) + 4 MHz + the Channel BW assigned, where Channel BW is as defined in sub-clause 5.4.2. Operations below this point are for further study. NOTE 1: Notes in the tables shall be reviewed after June 2012 because of PHS band operation

change

NOTE 2: For measurement conditions at the edge of each frequency range, the lowest frequency of

the measurement position in each frequency range should be set at the lowest boundary of the frequency range plus MBW/2. The highest frequency of the measurement position in each frequency range should be set at the highest boundary of the frequency range minus MBW/2. MBW denotes the measurement bandwidth (300 kHz).

Table 6.6.3.3.5.2-1: Additional requirements (network signalled value “NS_07”)

Frequency band (MHz) Channel bandwidth / Spectrum emission limit (dBm) 10 MHz 769 ≤ f ≤ 775 -57 6.25 kHz Measurement bandwidth