迈普交换机配置指导书

迈普交换机配置指导书

1．通过Console口配置交换机（同HW2016一样）

? 通过配置线将终端的RS-232串口与交换机的Console口相连。

配置用PCMyPower S3000BPC机串口配置口

2．迈普交换机基本配置 ena

con t 进入配置模式

vlan 2 创建vlan 2

port 0/0 tag ex

layer2-mode disable 关闭2层模式

interface sw0 进入 SW0接口

ip address 192.168.x.x 255.255.255.0 配置管理地址 x范围(2-254)

vlan-id 2 管理vlan exit

ip route 0.0.0.0 0.0.0.0 192.168.x.1 静态路由,指向管理地址x网关

enable password level 15 admin 为交换机密码

igmpsnoop en 打开组播 exit wr

3．中兴交换机配置实例

Switch# show run

Build configration... done

Current configration: 1701 bytes

user admin password 7 OWRW[WWW\\W user admin privilege 15

enable password OWRW[WWW\\W encrypt

service password-encrypt service login-secure

layer2-mode disable

vlan 1

description default port 0/0-0/15 untagged vlan 2

description VLAN0002 port 0/0 tagged vlan 1065

description VLAN1065 port 0/0-0/15 untagged vlan 2103

description VLAN2103 port 0/0-0/15 tagged vlan 2104

description VLAN2104 port 0/0-0/15 tagged exit

igmpsnoop enable

!slot 0 port 0/1 pvid 1065

storm-control disable exit port 0/2 pvid 1065

storm-control disable exit port 0/3 pvid 1065

storm-control disable exit port 0/4 pvid 1065

storm-control disable exit port 0/5 pvid 1065

storm-control disable exit port 0/6 pvid 1065

storm-control disable exit port 0/7 pvid 1065

storm-control disable exit port 0/8 pvid 1065

storm-control disable exit port 0/9 pvid 1065

storm-control disable exit port 0/10 pvid 1065

storm-control disable exit port 0/11 pvid 1065

storm-control disable exit port 0/12 pvid 1065

storm-control disable exit port 0/13 pvid 1065

storm-control disable exit port 0/14 pvid 1065

storm-control disable exit port 0/15 pvid 1065

storm-control disable exit

interface loopback0

ip address 127.0.0.1 255.0.0.0 exit

interface sw0

ip address 192.168.14.2 255.255.255.0 vlan-id 2 exit

ip route 0.0.0.0 0.0.0.0 192.168.14.1

Switch# 3.1 举例说明

例：1端口为主端口，2,3端口为下挂交换机端口，4,5端口为普通农带，6-10端口为家庭网关数据，11-12为单个可视电话用户，13端口为网络IP电话用，14端口为带网络IP电话的家庭网关网户，15端口为IP电话用户。配置如下：

Switch# configure terminal

% Enter configuration commands, one per line. End with CNTL+Z.

Switch(config)#vlan 2

Switch(config-vlan2)#port 0/0-0/3 ta

Switch(config-vlan2)#vlan 1000

Switch(config-vlan1000)#port 0/0-0/3 ta